High Tensile Acrylic Elastomeric Roof Coating.  Highest performance plasticizer-free, single component, water-based, 100% acrylic elastomeric coating for SPF and most substrates.

Technical Data Sheet (Professional Use Only)

---

DESCRIPTION

• High-performance, plasticizer-free, single-component, water-based, 100% acrylic elastomeric roof coating for spray, brush, or roller application
• Industry-leading tensile strength and elongation for a durable, long-lasting waterproof membrane
• Formulated with UV-resistant pigments and biocides to help resist weathering and discoloration from dirt accumulation
• Excellent adhesion to a variety of substrates including metal, single-ply roofing systems, wood, and concrete
• Breathable membrane allows trapped moisture to escape while maintaining waterproof protection

---

RECOMMENDED USES

Designed as a protective coating for roofing systems including:

• Galvanized metal
• Concrete
• PVC
• Hypalon
• EPDM
• Polyurethane foam
• Primed smooth and granulated asphaltic surfaces

Primers may be required depending on substrate type.

---

COLORS

Standard colors include:

• White
• Light Gray
• Medium Gray
• Charcoal
• Tan

Custom colors available upon request.

---

PACKAGING

• 275 gallon tote (1040.9 liters)
• 55 gallon drum (208.2 liters)
• 5 gallon pail (18.9 liters)

---

PHYSICAL PROPERTIES

• Volume Solids: 55% ±2%
• Weight Solids: 66% ±2%
• Tensile Strength: 500 ±50 PSI
• Elongation: 600% ±50%
• Permeability: 14 ±3
• Tear Resistance: 133 PSI
• VOC: < 50 g/L
• Hardness (Shore A): 50–55
• Reflectivity: 87%
• Emittance: 0.90
• SRI: 107
• Viscosity: 110 ±10 KU
• Density: 11.1 lbs/gal
• Flashpoint: None
• Shelf Life: 24 months (unopened, stored 40°F–70°F / 4°C–21°C)
• Clean Up: Water

Meets ASTM and industry performance standards including ASTM D6083. Fire rated and energy compliance qualified.

---

SURFACE PREPARATION

All surfaces must be clean, dry, and free of contaminants including dust, oil, loose coatings, and debris.

• Pressure wash recommended (minimum 2000 PSI with fan tip)
• Mildew should be treated and rinsed thoroughly
• Cracks and defects should be repaired prior to coating

Substrate Guidelines:

• Masonry: Cure minimum 30 days; prime before coating
• Metal: Clean rust and prime appropriately
• EPDM: Use compatible primer/cleaner
• PVC / Hypalon / aged TPO: Use approved primer
• Polyurethane foam: Apply directly within 24 hours of installation
• Asphalt surfaces: Use appropriate base coats
• Other substrates: Follow approved primer guidelines

---

APPLICATION

Can be applied by brush, roller, or spray on clean, dry surfaces.

• Surface must be at least 75°F for spraying
• Each coat must be fully dry before applying additional layers
• Contaminated surfaces must be cleaned prior to recoating

---

APPLICATION PROPERTIES

• Coverage Yield: 1 gal per 100 sq ft (approx. 8.8 dry mils)
• Dry Time: ~90 minutes at 75°F / 50% humidity
• Recoat Window: 6+ hours
• Full Cure: ~30 days

---

COVERAGE RATE

Apply at approximately:

• 1.5 gallons per 100 sq ft (24 wet mils)

Surface texture and environmental conditions may affect final thickness.

---

ENVIRONMENTAL CONDITIONS

• Do not apply below 50°F or if temperatures may drop below 32°F within 24 hours
• Avoid application when rain or dew is expected before drying
• High humidity and cool temperatures may extend cure time
• Multiple thin coats may be required in marginal conditions

---

LIMITATIONS

• Not recommended for slopes under 1/8 in 12
• Not suitable for ponded water conditions
• Must be fully dry before exposure to moisture
• Not intended as a vapor barrier or thermal barrier
• Cure requires full water evaporation

---

SAFE PRACTICES

For professional use only. Users should be familiar with proper handling, safety procedures, and application methods prior to use.

---

APPLICATION EQUIPMENT

Brush

• Synthetic filament brush

Roller

• 1¼” nap roller

Spray Equipment

• Minimum 30:1 pump ratio
• 2.5+ GPM output
• Proper filtration (30 mesh or larger)
• Compatible high-pressure hose system
• Self-cleaning reversible spray tip (.027–.039 orifice, 40°–50° fan)
• Industrial-grade spray gun system recommended

SDS Report